Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Duct Repair & Sealing in Atlanta: What to Know First
We provide independent Abatement Technologies duct repair & sealing throughout Atlanta, with most residential jobs completed in a single scheduled visit. A written flat price, typically $249 to $399 depending on system size and access, is delivered before any panel comes off. Every job ends with a documented photo record of every duct run, and the 365-Day Done Right Promise applies in writing, not as a verbal courtesy.
This page is for Atlanta homeowners who have identified Abatement Technologies equipment in their HVAC system and need duct sealing, flex duct repair, metal duct repair, or air leak remediation. Whether you’re in a 2019 build near West End with Abatement Technologies HEPA filtration add-ons, or a Cascade Heights split-level where the original flex has sagged at the plenum connection, we treat the brand’s specific failure modes as documented facts, not guesswork. Call (470) 495-9370 for a free estimate with a written price before work starts.
How Abatement Technologies Products Fail - and How We Fix Them
- P600-series HEPA filtration units: The negative-pressure housings on these units develop gasket fatigue where the filter frame meets the duct collar, especially in Atlanta’s humidity cycles. We see this as a measurable air leak at the filter interface, not a filter failure. Our fix is a mastic sealant rebuild with OEM-spec gasket replacement, pressure-tested after.
- Abatement Technologies CAP600-UV air purifier add-ons: The 5-inch duct tap for these UV units is often field-cut too aggressively during original install, leaving a gap at the sheet metal penetration that widens as the HVAC cycles expand and contract. We repair with a custom-fabricated collar and mechanical seal, not tape, because tape releases at 140°F plenum temps.
- Flex duct on Abatement Technologies AHU hookups: The brand’s air handlers specify a tight radius at the supply plenum that Atlanta installers sometimes exceed, creating a kink that traps moisture and collapses the inner liner. We replace the damaged section with properly supported flex, sized to Abatement Technologies static pressure specs, and photograph the sag before and after.
- BD2KL decontamination system ducting: These commercial-grade negative-air machines, sometimes retrofitted into large Atlanta homes, use high-tensile flex that fatigues at the clamp points after 18 to 24 months of pulse operation. We install abrasion sleeves and upgraded constant-tension clamps at stress points.
- Abatement Technologies HEPA500 negative air machines (whole-home configurations): The 12-inch inlet ducting on whole-home setups develops leaks at the quick-connect fittings where the locking ring wears against the Atlanta clay-heavy dust load. We replace the worn fitting with a flanged mechanical connection and seal with mastic rated for negative-pressure duty.
Our Abatement Technologies Duct Repair & Sealing Process
- 1
System identification and photo baseline. We confirm the Abatement Technologies model series, document the install date if visible, and photograph every accessible duct run before touching anything. The camera doesn’t negotiate.
- 2
Leak detection and scope write-up. We pressurize the system and use smoke pencil or theatrical fog to locate leaks, then write the scope: what needs sealing, what needs replacement, and what meets spec. Haven Standard Clause 1 requires the written price at this stage.
- 3
Parts decision: OEM or verified aftermarket. Abatement Technologies proprietary collars and gasket sets are available through HVAC supply houses with a 2-day lead time in Atlanta. For standard flex and mastic, we use quality aftermarket that meets or exceeds manufacturer pressure ratings. We state which we’re using and why.
- 4
Repair execution with access documentation. Every cut, seal, and clamp is photographed. Metal repairs get mastic plus mesh. Flex repairs get proper support strapping at 4-foot intervals. We work to Abatement Technologies static pressure tolerances, not generic “good enough.”
- 5
Post-repair pressure test and photo record delivery. We re-test at operating pressure, deliver the before-and-after photo set to the customer, and file the 365-Day Done Right Promise in writing. If the pressure reading doesn’t improve, we find why before leaving.
BeforeAfterWhat Abatement Technologies Duct Repair & Sealing Costs in Atlanta
| Scenario | Typical Range | What Moves the Price |
|---|---|---|
| Single leak seal (mastic, accessible) | $249 - $299 | Height of duct, amount of degraded tape to remove |
| Flex duct section replacement (1-2 runs) | $299 - $349 | Duct diameter, attic temperature, length of run |
| Metal duct repair with collar fabrication | $349 - $399 | Custom sheet metal work, UV add-on reintegration |
| Whole-system seal after Abatement Technologies HEPA retrofit | $349 - $399 | Number of new penetrations to seal, filter housing gasket condition |
These are whole-system flat prices, not per-vent arithmetic. The price you approve in writing is the price on the invoice. No post-work surprises, no “while we were up there” add-ons. Call (470) 495-9370 for a free estimate with an exact written number for your Abatement Technologies system.
Why Atlanta Homeowners Call CleanRun Air Duct Cleaning Atlanta for Abatement Technologies Work
We’ve been running jobs across Atlanta since 2013, and we’ve learned that Abatement Technologies equipment shows up in two kinds of homes: new builds where the builder spec’d filtration-heavy HVAC, and retrofits where a previous owner wanted hospital-grade air. Both scenarios have specific failure patterns that generic duct crews miss because they’re looking for “dirty ducts,” not pressure-tested seals at proprietary fittings.
Tomas Reyes and our crew know the difference between an Abatement Technologies CAP600-UV duct tap and a standard 6-inch register boot. We also service Lennox, Trane, and Carrier systems, which matters when your Atlanta home has mixed-brand equipment and the leak is at the interface, not inside one manufacturer’s box. Every technician is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. The 365-Day Done Right Promise is in writing on every job. And the photo record is delivered before we ask for payment.
FAQs
No, if the work is performed by a qualified technician using parts that meet manufacturer specifications. As an independent Abatement Technologies service provider, we document every part number and seal method so warranty claims remain valid. We keep that record with your job file. Call (470) 495-9370 if you need a copy for a warranty submission.
OEM gaskets, collars, and proprietary fittings typically arrive within two business days through Atlanta HVAC supply channels. Standard flex duct, mastic, and clamps are on our trucks. We schedule the repair once parts are confirmed, not before. You’ll know the timeline when you get your written price.
Repair is the right call when the air handler and filtration unit are functioning and the damage is localized to duct runs, seals, or fittings. We recommend replacement only when multiple leaks indicate systemic install failure or when the duct material itself has degraded past salvage. We’ll show you the camera evidence and quote both options in writing if you want to compare.
We measure static pressure before and after repair, and we deliver timestamped photos of every sealed joint and replaced section. The pressure improvement is a number you can read; the photo record is documentation you can keep. Haven Standard Clause 5 requires both. If the numbers don’t move, we keep working until they do.
Yes. We are independently owned and operated, not affiliated with or authorized by Abatement Technologies, Lennox, Trane, or Carrier. Multi-brand experience is an advantage: we understand how Abatement Technologies negative-pressure components interact with Trane variable-speed blowers or Carrier humidity controls, which is common in Atlanta’s higher-end retrofits. The repair methods we use are manufacturer-spec, not brand-limited.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Atlanta at CleanRun Air Duct Cleaning Atlanta, serving Atlanta and nearby areas.