Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Atlanta: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Atlanta for homeowners who need evaporator coils, blowers, condensers, air handlers, and heat exchangers cleaned without the guesswork. A typical Abatement Technologies system cleaning runs $249 to $399 depending on how many components need attention, and we put that price in writing before any panel comes off. Most Abatement Technologies jobs in Atlanta are completed in a single scheduled visit, with before-and-after photos of every component included in your job record.
This page is for Atlanta homeowners with Abatement Technologies equipment installed between 2015 and 2025, especially those in older neighborhoods like Cascade Heights, Grant Park, or Decatur where the humid subtropical climate accelerates coil fouling and blower debris buildup. If your Abatement Technologies air handler is running louder, your energy bill climbed last summer, or you’re smelling must when the system cycles on, the issue is usually visible once the access panel is off. Call (470) 495-9370 for a free written estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 360 Series evaporator coil fouling in Atlanta’s high-humidity summers. The PREDATOR 360’s coil design runs a tighter fin pitch than comparable commercial units, which traps more biological growth when July humidity sits above 75% for weeks. We see this in Buckhead basements and Midtown mechanical closets where the drain pan overflows before the homeowner notices reduced airflow. Our fix: full coil removal and foaming clean with Abatement Technologies-compatible non-acid cleaner, followed by a drain line flush and pan treatment. The camera shows the fin gap before we start and after we finish.
- BD2M blower motor debris accumulation from skipped filter changes. The BD2M’s direct-drive blower sits low in the cabinet, making it a debris magnet when filters get stretched past three months. In Kirkwood renos and East Atlanta flips, we regularly find the blower wheel coated in a mat that throws the assembly out of balance. Our fix: blower removal, ultrasonic cleaning of the wheel and housing, and static pressure verification against the manufacturer’s baseline. We photograph the imbalance crack pattern on the shaft if present.
- HEPA-CARE 500 air handler cabinet corrosion from condensate pooling. The 500 series uses a galvanized cabinet that corrodes at the floor seams when the secondary drain backs up, common in Atlanta’s pollen-heavy springs when algae blooms clog condensate lines. Our fix: cabinet disassembly, corrosion remediation with HVAC-safe encapsulant, and installation of a float switch if none exists. We document the seam integrity with photos.
- ABATEMENT AIRE coil treatment breakdown from incompatible aftermarket chemicals. We’ve cleaned up after competitors who used generic foaming agents on Abatement Technologies coils, leaving a residue that degrades the factory-applied antimicrobial coating. The coating flakes, the fins oxidize faster, and the homeowner gets a $1,200 coil replacement quote two years later. Our fix: manufacturer-compatible coil treatment only, verified by SDS sheet match, with the product lot noted on your written job record.
- Portable HEPA unit blower fatigue in whole-home supplemental systems. Homeowners in Sandy Springs and Brookhaven sometimes pair Abatement Technologies portable HEPA units with their central system, and the auxiliary blowers fatigue from continuous operation during Atlanta’s extended pollen seasons. Our fix: integrated cleaning of both the central system and the supplemental unit, with airflow balancing to reduce redundant load. We measure and record CFM at each register before and after.
Our Abatement Technologies HVAC Cleaning Process
- 1
Pre-job walkthrough and written price. We inspect the Abatement Technologies model plate, verify the installation date, and identify which components need attention. Haven Standard Clause 1 requires the written price before any work starts. For a standard evaporator coil and blower cleaning, that’s typically $249 to $349; adding condenser and heat exchanger runs $349 to $399.
- 2
Diagnostic photography. We open the cabinet and photograph every component in its found condition. The camera doesn’t negotiate - what we see is what you see, before we explain what it means.
- 3
Component-specific cleaning protocol. Evaporator coils get foaming clean with Abatement Technologies-compatible cleaner and low-pressure rinse. Blowers get ultrasonic bath or hand-cleaned depending on debris type. Condensers get fin straightening and coil wash. Heat exchangers get visual inspection and soot removal if needed. We use Rotobrush and Nikro equipment on duct connections where applicable.
- 4
OEM-vs-aftermarket parts decision, documented. If we find a failed component - a cracked drain pan, a corroded blower bracket - we source OEM Abatement Technologies parts when available, or quality aftermarket with equivalent specs when lead times stretch past what makes sense for your system. The choice and reasoning go on your written record.
- 5
Post-clean testing and photo record delivery. We run the system through a full cycle, measure supply and return temperatures, and verify static pressure against baseline. Your documented photo record - every component, before and after - is delivered as a standard deliverable before we leave.
- 6
365-Day Done Right Promise activation. The written guarantee goes into effect the moment we start the truck. If anything we cleaned fails due to our workmanship within 365 days, we make it right.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Atlanta
| Service Scope | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning only | $249 - $299 | Coil accessibility, fin corrosion severity, drain pan condition |
| Evaporator coil + blower cleaning | $299 - $349 | Blower wheel debris load, motor bearing condition |
| Full system clean (coil, blower, condenser, heat exchanger) | $349 - $399 | Condenser fin damage, heat exchanger soot level, cabinet corrosion |
| Air handler cabinet remediation + coil treatment | $379 - $449 | Corrosion extent, secondary drain modification needed |
Every price is system-specific and agreed in writing before work begins. No per-vent add-ons, no equipment-rental surprises, no “while we’re here” upsells. The price we write is the price you pay. Call (470) 495-9370 for a free estimate - we’ll put a number next to your Abatement Technologies model while you’re on the phone.
Why Atlanta Homeowners Call CleanRun Air Duct Cleaning Atlanta for Abatement Technologies Work
We’ve been running Abatement Technologies jobs across Atlanta since 2013 - 52,000 homes, every one with a written price first and a photo record at the end. Tomas Reyes and our crew know the difference between a PREDATOR 360 and a HEPA-CARE 500 without checking the manual, and we carry the tools to service both. Our equipment roster includes Abatement Technologies-compatible cleaners and Rotobrush, Nikro, Honeywell, Aprilaire, and Guardsman tools - brands you can look up before you book.
We’re also fluent in Lennox, Trane, and Carrier systems, which matters when your Abatement Technologies supplemental equipment ties into a mixed-manufacturer setup. Haven Standard Clause 3: Verified Crews means every technician is background-checked, uniformed, and identified by name before arrival. The 365-Day Done Right Promise is backed in writing on every job, not just stated in marketing copy.
FAQs
No - professional cleaning by an independent service provider does not void your Abatement Technologies warranty, provided no components are altered or non-OEM parts are installed without documentation. We use manufacturer-compatible cleaning agents and note every product by lot number on your job record. If your system is still under factory warranty, we flag any component concerns that should go through your installing dealer first. Call (470) 495-9370 if you need help reading your warranty dates.
Every Abatement Technologies job includes a documented photo record of every component, before and after, delivered to you before we leave. We also measure and record supply/return temperatures and static pressure. If a competitor told you your coils were cleaned but can’t show you the inside of the cabinet, they ran a shop vac near the registers and called it a day.
Replace if the heat exchanger is cracked, the cabinet is corroded through at multiple seams, or repair costs exceed 40% of replacement within a system that’s already past 12 years. Clean and repair if the issue is isolated to a fouled coil, debris-loaded blower, or backed-up drain - all fixable for $249 to $399 with a 365-day workmanship guarantee. We give you the numbers for both paths in writing.
A single-component cleaning (coil or blower) typically takes 90 to 120 minutes on site. A full system clean runs 3 to 4 hours including testing and photo documentation. We schedule by the job, not by the hour, so there’s pressure to rush through your cabinet.
The $79 coupon model relies on arriving at your door and finding “problems” that multiply the price once the crew is inside. We don’t do that. Haven Standard Clause 1: the written price is the price. For Abatement Technologies HVAC cleaning, that’s $249 to $399 depending on scope, agreed before we touch a panel. Bring us a competitor’s written estimate and we’ll provide a free second opinion with our number next to it.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Atlanta at CleanRun Air Duct Cleaning Atlanta, serving Atlanta and nearby areas.